The Swagman XTC4 4 Bike Rack # S64665 can be used with a hitch adapter, like the Brophy Hitch Adapter # HTAD. However, there are some things to consider with a hitch adapter.
When using a hitch adapter, the tongue weight of your vehicle's hitch will be reduced by 50 percent. So if your trailer hitch has a tongue weight capacity of 200 pounds, with a hitch adapter it will have a tongue weight of 100 pounds. This means that the bike rack and all bikes loaded will need to weigh less than... view full answer...
The reason that you can't use a Class II adapter in a Class I hitch receiver is that most Class I hitch receivers have a lip or stopper that keeps you from using the longer shank of the Class II adapter in the lower capacity Class I hitch. You would instead want to use an adapter like the # HTAD which is designed for use in both Class I and II hitch receivers if you needed to use an adapter. It should be noted that when using an adapter, it will reduce your tongue weight capacity by 50%,... view full answer...
Great question! I went ahead and reached out to my tech at Hollywood Racks, and he confirmed that using a 2-1/2" to 2" hitch adapter is completely fine to use with the RV Rider # HLY64FR.
If you need a hitch reducer for your 2-1/2" hitch, I recommend using the Curt Hitch Reducer # C45405. This adapter does not add an extension and comes with a 5/8" pin hole diameter. This reducer does not decrease the weight rating of your hitch. view full answer...
The extra hole on the side of the Replacement Aluminum Hitch Adapter Sleeve for Saris 1-1/4" Hitch Bike Racks # SA3032 that you referenced is use for attaching the adapter with the included nut and bolt to the shank of the bike rack. Basically the bolt runs through the adapter and then through the shank of the bike rack and then secured with the nut and you are set. The larger hole is then for the hitch pin of the rack. view full answer...
By receiver end I take it that you mean the solid shank end of the Roadmaster High-Low Adapter # RM-048-4 that fits in the trailer hitch receiver on your motorhome. If this is the case then the Curt Hitch Extender # C45791 is designed the exact same way.
For a 4" drop/rise adapter that has a hollow shank you can use an anti-rattle device like part # 63232 we have the High-Low Adapter # BLU34TR. This allows you to insert the block from the anti-rattle pin to help keep this from moving in... view full answer...
The Ranch Hitch Universal 5th-Wheel-to-Gooseneck Coupler Adapter # AM3100 is definitely suitable for long term use and will not put any excess strain on the trailer. The adapter is a good solution for anyone that wants to use their 5th-wheel camping trailer with the gooseneck hitch on their truck. Keep in mind, this adapter is designed to be used with standard pin boxes only. Do not use with a cushioned or air ride pin box.
I have attached a picture which outlines the measurements you... view full answer...
The answer is yes, a Reese 5th wheel hitch like the # RP30047 can absolutely be used in your 2018 Ford F-250 with the factory puck system. In order to do so, all you would need is an adapter, which is the following part:
- Reese Elite Series Underbed Rail Adapter # RP30156
This adapter will mount directly in your F-250's puck system (either the long bed or short/standard bed) and allow you to mount your Reese 5th wheel hitch directly in the adapter. view full answer...
In order to use this lighted Ford hitch cover, you will need an adapter, product # PK12716, that will adapt your 7 Pole to a 4 Pole. This will allow you to plug the hitch cover into the 4 Pole adapter and be on your way! view full answer...
Whenever you use a hitch adapter like the Hitch Adapter 1-1/4" to 2" Trailer Hitch Receiver # 80303 you affectively cut your trailer hitches capacity by half.
So, with your class I hitch already has a fairly low capacity, using a hitch adapter will reduce your capacity to almost nothing.
Instead, I recommend using a bike rack that is compatible with a class I hitch, like the:
-Thule Hitching Post Pro - Folding Tilting 4 Bike Rack w Anti-Sway # TH934XTR.
This bike rack isn't going to... view full answer...
Due to the lower tongue weight capacities of trailer hitches that have 1-1/4 inch receivers, there are no dual hitch adapters available for a 1-1/4 inch trailer hitch receivers. The adapters are only available for 2 inch trailer hitch receivers.
If you have a 2 inch trailer hitch and a bike rack or cargo carrier with a 1-1/4 inch shank, you could use a hitch reducer like part # HT02 to allow you to use your hitch mounted accessory with the dual hitch adapter. Please note, the dual hitch... view full answer...
It sounds like you have the factory 5th wheel prep package in your 2017 Ram 2500. If this is the case, then you will want the Reese Ram OEM Rail Adapter, # RP30154, to use your Husky 5th wheel hitch in this truck. This adapter mounts in the pucks in your truck bed and provides mounting slots that match those of industry standard above-bed base rails.
Keep in mind, this adapter will add about 2 inches of height to your 5th wheel hitch. Demco offers a slightly shorter adapter, part # DM6099.... view full answer...
The adapter of the Andersen Ultimate Connection 5th Wheel Trailer Hitch System # AM3200 will stay exactly where it is so long as you follow the install directions. The 40 lb weight of the actual hitch will not affect the adapter in regards to it turning.
I also reached out to Andersen in regards to the adapter staying parallel or turning with your trailer and was told that it "didn't move at all."
This lightweight hitch will fit industry-standard fifth wheel rails, has a 20,000 lb capacity... view full answer...
If you have an M5 series 5th Wheel Hitch, like the Reese M5 Series 5th Wheel Trailer Hitch, # RP30921, that you have referenced, no adapter is required.
There is an adapter kit to adapt the Signature Series 5th Wheel Hitches to the pre-installed pucks on the 2011 Ford F-350 Super Duty. You would need to use the Reese Signature Series Hitch Adapter, # RP58419. This kit allows the Signature Series 5th Wheel Trailer Hitches to fit in the Ford installed pucks. Rails are not required if you... view full answer...
We offer a hitch adapter that will adapt a 1-1/4 receiver to a 2 inch, part # HTAD.
Keep in mind that using an adapter will lower the tongue weight capacity of your hitch by 50 percent. For instance, if your current hitch has a 350 lb tongue weight capacity, using an adapter will lower the capacity to 175 lbs. This will mean that the hitch accessory (bike rack or cargo carrier) plus what ever is carried on it can weigh no more than 175 lbs. This is caused by the additional leverage placed... view full answer...
Yes, the Convert a Ball Adapter part # CAB-C5G is height adjustable. It can be adjusted from 12 to 16 inches in height. I attached an install video for you to check out as well. view full answer...
In the install instructions for the head of the Reese M5 27k fifth wheel hitch recommend a grease needle adapter with a grease gun like part # L30132 to apply grease to the grease fitting on top of the hitch. We don't have the needle adapters but a local hardware store or even elsewhere online would pretty easily have them as they are very common. view full answer...
You are correct. The locking arms are what locks the Reese 5th Wheel Adapter, part # RP30154 in place to the pucks in the bed of your 2014 Dodge Ram. It would be impossible to move the arms without removing the hitch first.
Also, the weight of a fifth wheel hitch added to the weight of this adapter at nearly 75 lbs would make it even more difficult to handle. view full answer...
The Sidewinder works by moving the pivot point from the hitch and king pin coupling point to a distance of 22" back from the center of that point. It does this using a wedge at the mounting point to prevent the king pin from rotating at those points of contact. The Sidewinder, unlike typical pin boxes, have a rotating turret. This is where rotation happens for turning instead of at the hitch point.
The person you spoke with from Andersen is correct that if you install the lock out... view full answer...
We do have a dual hitch adapter that may work for you, but the Roadmaster Dual Hitch Receiver Adapter # RM-077-4 is not designed to be used for towing a trailer. It's designed to carry a bike rack or cargo carrier while flat towing a vehicle.
The Curt Dual Receiver # D-192 can be used for towing using the bottom receiver opening. Top receiver would be used for you winch. Also, you should know that using a hitch adapter, such as this, will reduce your capacity by 50 percent. view full answer...
Using an adapter like the Roadmaster Dual Hitch Receiver Adapter, 4" Drop/Rise # RM-077-4 in your Curt trailer hitch receiver # 31302 is not an issue as long as you are aware of the load limits. The vertical load limit on this hitch is 500 lbs and the tongue weight limit on the adapter is 400 lbs. These are basically the same thing. The issue with using an adapter is that it decreases the capacity of the hitch's tongue weight or in the case of front mounted hitches the vertical load... view full answer...
Go To Results